- Wire Rope & Rigging Hardware
- Wire Rope Assemblies
- Balustrade & Trellis
- Cutters & Tools
- Architectural
- Tie Bar Systems
- Display Systems
Swageless Fork - Compression Fork
Swageless Fork - Compression Fork
Swageless Fork - self assembly stainless steel wire rope terminal
All in 316 grade stainless steel
Swageless Fork
| Available Options | Wire (mm) |
P (mm) |
C (mm) |
T (mm) |
L (mm) |
A/F (mm) |
Code | Price (ex VAT) (1x19) | |
|---|---|---|---|---|---|---|---|---|---|
| 3mm Swageless Fork : | 3 | 6 | 13 | 6.3 | 30 | 9.5 | CTF-030 | £16.81 | |
| 4mm Swageless Fork : | 4 | 8 | 16 | 8 | 40 | 11 | CTF-040 | £19.80 | |
| 5mm Swageless Fork : | 5 | 9.5 | 19 | 10 | 47 | 14 | CTF-050 | £24.08 | |
| 6mm Swageless Fork : | 6 | 11 | 22 | 11 | 50 | 19 | CTF-060 | £33.23 | |
| 7mm Swageless Fork : | 7 | 12 | 25 | 12.7 | 58 | 20 | CTF-070 | £36.70 | |
| 8mm DS Swageless Fork : | 8 | 12 | 25 | 12.7 | 63 | 22 | CTF-080-DS | £47.58 | |
| 8mm Swageless Fork : | 8 | 14 | 28 | 14 | 70 | 22 | CTF-080 | £53.00 | |
| 8mm US Swageless Fork : | 8 | 16 | 32 | 16 | 72 | 26 | CTF-080-US | £57.27 | |
| 10mm Swageless Fork : | 10 | 16 | 32 | 16 | 78 | 26 | CTF-100 | £68.81 | |
| 12mm Swageless Fork : | 12 | 19 | 38 | 19 | 93 | 32 | CTF-120 | £97.19 | |
| 14mm Swageless Fork : | 14 | 22 | 45 | 22.2 | 106 | 36 | CTF-140 | £180.46 | |
| 16mm Swageless Fork : | 16 | 25.4 | 50 | 25.4 | 126 | 40 | CTF-160 | £227.09 | |
| 19mm Swageless Fork : | 19 | 28 | 58 | 28.6 | 133 | 44 | CTF-190 | £420.18 | |
| 22mm Swageless Fork : | 22 | 32 | 64 | 32 | 146 | 52 | CTF-220 | £546.91 | |
| 26mm Swageless Fork : | 26 | 35 | 70 | 35 | 167 | 64 | CTF-260 | £676.16 |
Information
Stainless steel swageless fork terminals for 1x19, 7x7, 7x19 and Dyform wire rope. Norseman type swageless fitting.
Swageless fork (jaw or yoke) terminals are assembled by hand using spanners. Swageless forks are a good alternative to swaging.
Correctly assembled, swageless fork fittings will be at least as strong as the cable.
When ordering please state whether you require the swageless fitting for 1x19, 7x19, 7x7 or dyform wire - please add this at Step 2 of the buying process.
Swageless fittings are also available for use with imperial size wire. Please contact us for further details.
Swageless Termination Video Demonstration
How to...
Cut the wire to length. The edge of the wire must be square. Try wrapping a piece of tape around the end of the wire which will keep the strands in place while cutting. A clean cut will assist assembly.
Place the main body part over the wire rope as shown.
Untwist the outer wire strands by gripping firmly and twisting in the opposite direction to the lay of the wire. Keep unwinding the outer strands until you can clearly see the centre core wire.
Locate the cone, shown above.
Slide the thin end of the cone over the centre strand. You can force the cone open with a screwdriver blade if necessary.
Locate the crown ring, shown above.
Slide the crown ring over the core with the concave side to the cone.
There is a hole in the centre of the threaded stud, fork or eye.
Push the crown ring on with this part and the core will protrude by the correct amount.
Note how the crown ring (in red) and the core (in blue) should be seated.
Gently twist the outer strands of the wire rope back into position over the Cone. Firmly twist the Crown Ring in the direction of the lay while you position the outer strands in the slots.
Wire sizes up to 5mm require 2 strands per slot, wire sizes above 5mm have 1 strand per slot.
When all of the outer strands are in place the Cone and Crown Ring will remain in place with no assistance.
Make sure that each outer strand is not out of position and that each slot houses the correct number of strands.
At this stage you can test that the fitting has been assembled correctly by positioning the threaded end fitting on top of the Crown Ring.
The part should sit flush with none of the wire obstructing the threads of the end fitting.
Gently twist the body back up the wire and over the Cone and Crown Ring, rotating in the same direction as the lay of wire.
Screw the threaded end fitting tightly onto the body.
Do not apply thread locking solution at this stage.
Remove the end fitting and ensure that the outer strands and the crown ring have stayed in position.
Screw the threaded end fitting back into position and fix with Loctite 262 or some other suitable thread locking solution.
Go to Loctite
You haven't added anything into your basket yet
| Search by product code |

