Sta-Lok Eye - Swageless Rigging - DIY Terminal

Sta-Lok Eye - Self Fit Wire Rope Terminal - 316 Stainless Steel

Sta-Lok Eye - Self assembly stainless steel wire rope terminal, reusable alternative to swage.

Sta-Lok Eye - Swageless Fitting

Options	Wire (mm)	A (mm)	B (mm)	D (mm)	H (mm)	Code	Price (inc VAT)	Quantity
3mm Eye	3	17.9	10	5	6.5	033-03	£26.50	7-10 days
4mm Eye	4	20.3	14.7	5.8	8	033-04	£29.51	7-10 days
5mm Eye	5	24.4	18	7.5	10	033-05	£36.92	7-10 days
6mm Eye	6	31	22.2	9.5	13	033-06	£44.23	7-10 days
7mm Eye	7	32.5	24.6	10.5	13	033-07	£53.21	7-10 days
8mm - 1/2 Eye	8	35.7	27	12	13	033-08-1/2	£61.14	7-10 days
8mm - 5/8 Eye	8	35.7	27	13.5	16	033-08-5/8	£81.42	7-10 days
10mm Eye	10	41.1	29.2	13.5	16	033-10	£92.22	7-10 days
12mm Eye	12	42.8	33.3	19	19.5	033-12	£212.36	7-10 days
14mm Eye	14	55.6	38.1	20	22.5	033-14	£266.92	7-10 days
16mm Eye	16	59	40	20	22.5	033-16	£320.04	7-10 days
19mm Eye	19	68.3	49.2	27	28.6	033-19	£656.42	7-10 days
22mm Eye	22	82.6	60.3	33.3	35	033-22	£782.45	7-10 days
26mm Eye	26	86	60.3	33.3	35	033-26	£1,029.46	7-10 days

Tip: To view the product code and full product table on mobile please tilt your device to landscape.

Key Features:

316 grade stainless steel.

Sta-Lok terminals are reusable and are supplied with 1x19 wedges as standard.

Wedges for 7 strand & compacted strand wire ropes can be purchased separately.

No pre-measurement needed.

Quick and easy to install, only basic hand tools required.

Guaranteed stronger than wire rope.

Suitable for right hand and left hand lay wire rope.

Manufactured from 316 grade stainless steel.

Dimension Information:

PDF Data Sheet

Download Sta-Lok Eye Dimension Information

Sta-Lok Wire Connector Terminals - Technical Information - How to assemble

1. Cut wire rope and slide socket component over wire.

Wind tape around wire approx 12" (300mm) from end. This will prevent the socket from sliding down the wire.

TIP: If using a hacksaw to cut your wire rope, wind tape around wire to ensure a neat cut.

2. Unravel outer strands 2" to 3" (50-76mm) to expose central core.

TIP: Use a screwdriver to prise initial strands out of position.

3. Slide wedge component over central core of wire rope.

4. Reposition outer strands.

Turn outer strands either clockwise or anti-clockwise, depending on the lay of the wire, around the wedge. Ensure approx 1/8" (2-3mm) of the central core protrudes from the end of the wedge.

Outer strands should be evenly situated around the wedge. Care should be taken to ensure that a strand does not slip into the slit of the wedge.

TIP: Push the socket towards end of wire, while repositioning the outer strands, this will help control. When wire strands are in position, push socket firmly, as indicated to hold wires in position.

5. Final assembly.

Ensure former component sits in bottom of end fitting. Screw socket assembly into end fitting and tighten with spanners. The assembly is now complete.

TIP: Undue force is not required to terminate the wire.

Fitting instructions are supplied with each Terminal.