Sta-Lok Fork - Swageless Rigging - DIY Terminal
Sta-Lok Fork - 316 Stainless Steel
Sta-Lok stainless steel fork terminal for wire rope, reusable alternative to swage. Supplied with 1x19 wedge.
Sta-Lok Fork - Swageless Fitting
Options | Wire (mm) |
A (mm) |
B (mm) |
D (mm) |
P (mm) |
Code | Price (inc VAT) | Quantity |
---|---|---|---|---|---|---|---|---|
3mm Fork | 3 | 15.5 | 10 | 5.5 | 5 | 034-03 | £39.36 | |
4mm Fork | 4 | 21.1 | 14.7 | 6.4 | 6.4 | 034-04 | £44.35 | |
5mm Fork | 5 | 29.5 | 18 | 8 | 8 | 034-05 | £52.38 | |
6mm Fork | 6 | 37.1 | 22.2 | 11.1 | 10.9 | 034-06 | £57.56 | |
7mm Fork | 7 | 33.9 | 25.1 | 11.1 | 10.9 | 034-07 | £75.89 | |
8mm Fork | 8 | 43.9 | 26.3 | 13.7 | 12.6 | 034-08 | £90.78 | |
10mm Fork | 10 | 50.1 | 29.4 | 13.7 | 15.6 | 034-10 | £113.86 | |
12mm Fork | 12 | 46 | 33.3 | 19.4 | 18.5 | 034-12 | £281.10 | |
14mm Fork | 14 | 54 | 38.1 | 20.4 | 21.5 | 034-14 | £349.56 | |
16mm Fork | 16 | 72.7 | 40 | 20.4 | 25 | 034-16 | £446.93 | |
19mm Fork | 19 | 92 | 50 | 27.8 | 27.5 | 034-19 | £845.88 | |
22mm Fork | 22 | 92 | 60.3 | 34.9 | 33 | 034-22 | £1,000.02 | |
26mm Fork | 26 | 92 | 60.3 | 34.9 | 33 | 034-26 | £1,197.72 |
Tip: To view the product code and full product table on mobile please tilt your device to landscape.
Key Features:
316 grade stainless steel. |
Sta-Lok fork terminals are reusable and are supplied with 1x19 wedges.
Wedges for 7 strand & compacted strand wire ropes can be purchased separately.
No pre-measurement needed.
Quick and easy to install, only basic hand tools required.
Guaranteed stronger than wire rope.
Suitable for right hand and left hand lay wire rope.
Supplied with split pin.
Manufactured from 316 grade stainless steel.
Dimension Information:
PDF Data Sheet
Download Sta-Lok Fork Dimension Information
Sta-Lok Wire Connector Terminals - Technical Information - How to assemble
1. Cut wire rope and slide socket component over wire.
Wind tape around wire approx 12" (300mm) from end. This will prevent the socket from sliding down the wire.
TIP: If using a hacksaw to cut your wire rope, wind tape around wire to ensure a neat cut.
2. Unravel outer strands 2" to 3" (50-76mm) to expose central core.
TIP: Use a screwdriver to prise initial strands out of position.
3. Slide wedge component over central core of wire rope.
4. Reposition outer strands.
Turn outer strands either clockwise or anti-clockwise, depending on the lay of the wire, around the wedge. Ensure approx 1/8" (2-3mm) of the central core protrudes from the end of the wedge.
Outer strands should be evenly situated around the wedge. Care should be taken to ensure that a strand does not slip into the slit of the wedge.
TIP: Push the socket towards end of wire, while repositioning the outer strands, this will help control. When wire strands are in position, push socket firmly, as indicated to hold wires in position.
5. Final assembly.
Ensure former component sits in bottom of end fitting. Screw socket assembly into end fitting and tighten with spanners. The assembly is now complete.
TIP: Undue force is not required to terminate the wire.
Fitting instructions are supplied with each Terminal.
Questions & Answers
Reviews